Adhesive Mounting Kit.
Details and Installation Information
1) Orient the BareBones SS Display for Installation.
As shown in the illustration, flip the BareBones SS Display over and lay it on a flat, soft, non-abrasive surface to access the highlighted parts.
2) Remove Z-Bar Hanging Assembly, Cord Wraps, and Side Braces.
As shown in the illustration, using a #2 Phillips Head screwdriver, unscrew the (8) 8-32x1” pan head screws to remove the Z-Bar Hanging assembly, Cord Wraps, and Side Braces.
3) Install the Adhesive Mounting Kit.
As shown in the illustration, fasten the (8) 8-32x1” Phillips head screws (highlighted in RED) into the (8) 8-32 threaded inserts located on the rear of the BareBones SS Display which are also highlighted in RED. NOTE: DO NOT FORCE THE SCREWS INTO THE THREADED INSERTS OR OVER-TIGHTEN THEM AS YOU MAY DAMAGE THE DISPLAY. There are extra screws provided if neccessary.
4) Adhesive Mounting Kit Install Complete.
The Adhesive Mounting Kit when properly installed should resemble the illustration shown.
5) Retrieve and Orient the Piece the Display will be Mounted to.
As shown in the illustration, lay the piece you will be attaching the Adhesive Mounting Kit to on a flat, soft, non-abrasive surface.
6) Position the BareBones SS Display and Stand-Offs.
As shown in the illustration, place the BareBones SS Display w/ Adhesive Mounting Kit attached and the Stand-Offs onto the work piece you are using from the step above. NOTE: Make sure the LED PANELS have been backed out enough within the Adhesive Mounting Kit so that the mounting legs lay flat against the work piece you are using. Refer to the graphics and animation found in steps 8 & 9 below regarding how to accomplish this.
7) Mark the Mounting Feet and Stand-Offs.
As shown in the illustration, using a marker, outline where the Mounting Feet and Stand-Offs are positioned. This will allow you to apply the adhesive in the correct areas and subsequently reposition the Display and Stand-Offs in their correct locations.
8) Locate the Height Adjustment Screws.
As shown in the illustration, locate the (8) height adjustment screws.
9) Prepare for Adhesive Application.
As shown in the animation, raise the BareBones SS Display away from the workpiece about 1/4” (6mm) so as to prevent any adhesive from spreading onto any of the LED Panels. This is done by slowly turning each of the (8) individual height adjustment screws. Turning in the CLOCKWISE direction lowers the display, turning in the COUNTER-CLOCKWISE direction raises the display. NOTE: Each adjustment screw should be turned no more than a couple of turns, followed by the remaining screws and doing the same thing until the desired height is reached.
10) Apply the Adhesive.
As shown in the illustration, apply an appropriate amount of adhesive within the outlines created in step 7 above (the adhesive directions will indicate what the approprate amount used should be, based on the amount of coverage needed). NOTE: Make sure to test the adhesive you will be using in an incospicuous area to make sure that it does not damage the material. For the Acrylic Print example shown at the end of this page below, a liberal amount of Cyanoacrylate glue was used.
11) Attach the Display to the Work Piece.
As shown in the illustration, place the Mounting Feet of the Display and Stand-Offs into their correct (previously marked) locations. NOTE: Make sure to CAREFULLY remove any excess adhesive that may squeeze out from underneath the Mounting Feet into the area below the raised LED Panels. This is to make sure that the LED Panels will sit flush against the surface of the work piece once the adhesive has dried.
12) Set the LED Panels.
As shown in the animation and AFTER the adhesive has completely dried, lower the height of the BareBones SS Display so that the LED Panels sit flush against the surface of the work piece by slowly turning each of the (8) individual height adjustment screws. Turning in the CLOCKWISE direction lowers the display, turning in the COUNTER-CLOCKWISE direction raises the display. NOTE: Each adjustment screw should be turned no more than a couple of turns, followed by the remaining screws and doing the same thing until the desired height is reached. DO NOT OVER-LOWER the display as you will lift the Mounting Feet off the surface and damage the work piece. Good Practice will be lower the display until you can visually see that the LED Panels are touching the surface and no more.
13) Mount your Finished Piece.
Once you have completed the previous steps, you can configure and mount your creation using the steps found in the latest manual here. This photo is an example of the Adhesive Rear Mounting Kit applied to a 24”x16” Tyler Jordan “Van Siclen” Acrylic print.
